研究目的
To investigate the effect of stoichiometric and non-stoichiometric tungsten doping in bismuth vanadate (BiVO4) on its photoelectrochemical water splitting performance, focusing on enhancing conductivity and reducing recombination sites.
研究成果
Non-stoichiometric W doping with excess Bi and W in BiVO4 significantly enhances PEC water splitting performance by improving charge carrier density, reducing recombination sites, and optimizing surface states, without altering the band gap. This approach minimizes defect formation and enhances charge transfer kinetics.
研究不足
The study is limited to specific doping levels and compositions; scalability and long-term stability under practical conditions were not fully explored. The dip coating method may introduce variability in film uniformity.
1:Experimental Design and Method Selection:
The study involved synthesizing stoichiometric and non-stoichiometric W-doped BiVO4 films using a dip coating technique to compare their PEC performance. Theoretical models for defect chemistry and charge transport were considered.
2:Sample Selection and Data Sources:
Samples were prepared with specific compositions (Bi1-(x+d)V1-xWx+dO4, BiV1-xWx+dO4, BiV1-yWyO4 with x=0.008, y=0.03, d=0.005) on FTO glass substrates. Data were collected from XRD, XPS, SEM, UV-Vis, DRS, and electrochemical measurements.
3:008, y=03, d=005) on FTO glass substrates. Data were collected from XRD, XPS, SEM, UV-Vis, DRS, and electrochemical measurements. List of Experimental Equipment and Materials:
3. List of Experimental Equipment and Materials: FTO glass substrates, ammonium metavanadate, bismuth nitrate pentahydrate, nitric acid, ammonium metatungstate, K2HPO4 electrolyte, Na2SO3 hole scavenger, Pt wire, SCE reference electrode, solar simulator, potentiostat, XRD (PANalytical X'Pert PRO MRD), SEM (XL-30 Environmental FEG), XPS (Vacuum generator VG-220i-XL and GL30), UV-Vis spectrophotometers (Beckman Coulter DU 730 and Agilent Cary Series).
4:Experimental Procedures and Operational Workflow:
Clean FTO substrates were dip-coated in precursor solutions, dried, and heat-treated. Multiple layers were applied and calcined. PEC measurements were conducted in electrolyte with and without hole scavenger under illumination, using linear sweep voltammetry, Mott-Schottky analysis, and electrochemical impedance spectroscopy.
5:Data Analysis Methods:
Data were analyzed using EC-Lab software for equivalent circuit fitting, Kubelka-Munk function for band gap calculation, and standard equations for efficiency metrics.
独家科研数据包,助您复现前沿成果,加速创新突破
获取完整内容-
X-ray Diffractometer
PANalytical X'Pert PRO MRD
PANalytical
Used for phase analysis of BiVO4 electrodes.
-
Scanning Electron Microscope
XL-30 Environmental FEG
FEI
Used to examine surface morphology of electrodes.
-
UV-Vis-NIR Spectrophotometer
Agilent Cary Series
Agilent Technologies
Used for diffuse reflectance spectra.
-
FTO coated glass
2.3 mm thick, resistance 14 Ω/sq
Sigma Aldrich
Used as conductive substrates for electrode fabrication.
-
Ammonium metavanadate
99%
Sigma Aldrich
Precursor for vanadium in BiVO4 synthesis.
-
Bismuth nitrate pentahydrate
99.99%
Sigma Aldrich
Precursor for bismuth in BiVO4 synthesis.
-
Nitric acid
6 M
Sigma Aldrich
Used in precursor solution preparation.
-
Ammonium metatungstate
Precursor for tungsten doping in BiVO4.
-
XPS Spectrometer
Vacuum generator VG-220i-XL and GL30
Vacuum generator
Used for chemical environment analysis.
-
UV-Vis Spectrophotometer
Beckman Coulter DU 730
Beckman Coulter
Used for steady-state UV-visible measurements.
-
Solar Simulator
Newport 69907
Newport
Used as a light source for PEC measurements.
-
Potentiostat
Partstat-2273
Partstat
Used for electrochemical and impedance measurements.
-
Saturated Calomel Electrode
SCE
Used as reference electrode in PEC measurements.
-
Platinum Wire
Used as counter electrode in PEC measurements.
-
登录查看剩余12件设备及参数对照表
查看全部