- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Effects of phase transition temperature and preheating on residual stress in multi-pass & multi-layer laser metal deposition
摘要： To investigate the influences of phase transition temperature and preheating on the residual stress of multi-layer and multi-pass laser metal deposition (LMD), the multi-layer and multi-pass LMD, with and without preheating, were performed using five kinds of alloy with different phase transition features, and their residual stresses were measured using the hole drilling method. A finite-element (FE) model incorporating the phase transition was developed based on experimentally obtained physical property data. The results demonstrated that the low-temperature solid phase transition has a tensile stress relaxation effect, which leads to the formation of a compressive stress area. This relaxation effect was observed to decrease with the increase of the phase transition temperature. The high-temperature solid phase transition has no significant tensile stress relaxation effect during the multi-layer and multi-pass LMD process, which is different from the single track LMD. when the solid phase transition temperature is low, the preheating can improve the uniformity of the stress field only to a certain extent. However, when the preheating increases the lowest temperature of the thermal cycle and makes it higher than the starting point temperature of the solid phase transition, the tensile stress relaxation effect of the solid phase transition can be brought into full play.
关键词： Finite element analysis,Preheating,phase transition temperature,Residual stress,Laser metal deposition
更新于2025-11-28 14:24:20
-
Effects of TiO2 on the performance of silver coated on side-polished optical fiber for alcohol sensing applications
摘要： This work reports the experimental and numerical investigations on the effect of titanium oxide (TiO2) integrated on the optical fiber silver (Ag) surface plasmon resonance (SPR) sensors. In this paper, the numerical simulation is also analyzed using the finite element method (FEM) which shows good agreement. Results are compared with the experimental findings, focusing on the SPR phenomena for refractive index sensing using side-polished optical fiber, where the characteristics of the Ag layer with the integration of TiO2 are optimized. The essential parameters include the thickness of Ag namely 20 nm, 30 nm and 40 nm for optimization studies of SPR properties. TiO2 was then coated on the Ag thin layer to sense isopropanol at different concentration. It is shown that the combination of a 30 nm thickness of Ag layer with a dielectric TiO2 improves sensor performance in terms of sensitivity reading of 268 nm/RIU with a detection limit of 0.012. The main interest is to develop the device with cost effective, ease fabrication and less cumbersome of sensors using TiO2 which one of an alternative material to defeat the oxidation process and avoid charge recombination. If the sensitivity increases at a higher wavelength, it indicates that the TiO2 holds great potential in photonic applications.
关键词： Fiber Optic Alcohol Sensor,Surface plasmon resonance (SPR),Finite element method (FEM)
更新于2025-11-28 14:23:57
-
The effect of the TiO2 film on the performance of the optical fiber SPR sensor
摘要： We studied the effect of the Titanium Oxide (TiO2) film on the performance of the optical fiber SPR with two kinds of probes. The light guiding properties and sensing performance of the D-type optical fiber SPR sensor coated with TiO2 was studied numerically by finite element method (FEM) and the sensing performance of the multimode-single mode-multimode (MSM) hetero-core optical fiber SPR sensor coated with TiO2 was investigated experimentally. The simulation and experimental results for two kinds of probes consistently show that the absence of TiO2 film layer on the gold film can enhance the refractive index sensitivity and tune the resonance curve of the sensor from visible light to near-infrared.
关键词： Hetero-core structure,D-typed structure,Surface plasmon resonance,Finite element method,TiO2 film
更新于2025-11-28 14:23:57
-
Tailored nanocomposite energy harvesters with high piezoelectric voltage coefficient through controlled nanowire dispersion
摘要： Composites composed of piezoelectric nanomaterials dispersed in a flexible polymer have emerged as promising materials for highly durable and flexible energy harvesters and sensors. Although piezoelectric materials in their bulk form have a high electromechanical coupling coefficient and can efficiently convert mechanical energy to electrical energy, the ceramic form has low fracture toughness and thus they are limited in certain applications due to difficulty in machining and conforming to curved surfaces. Recently, additive manufacturing processes such as direct write, have been developed to incorporate piezoelectric nanowires into a polymer matrix with controlled alignment to realize printed piezoelectrics. Given the multiphase structure of a nanocomposite, it is possible to control the material structure such that the piezoelectric coupling and dielectric properties can be varied independently. In this paper, experimentally validated finite element (FE) and micromechanics models are developed for calculation and optimization of the piezoelectric voltage coefficient, g31, of a nanocomposite. It is shown that by using high aspect ratio nanowires with controlled alignment, the piezoelectric coupling can be disproportionately increased with respect to the dielectric constant which yields a g31 coefficient that can be enhanced more than seven times compared to the bulk piezoelectric material. Moreover, it is demonstrated that the use of high aspect ratio nanowires in the energy harvester resulted in significant improvement on the output electrical power of an energy harvester.
关键词： Energy harvesting,Nanowires,Finite element modeling (FEM),Voltage coefficient,Piezoelectric,The Mori-Tanaka method,Direct write,Nanocomposite
更新于2025-11-14 17:28:48
-
[IEEE 2018 28th International Symposium on Discharges and Electrical Insulation in Vacuum (ISDEIV) - Greifswald (2018.9.23-2018.9.28)] 2018 28th International Symposium on Discharges and Electrical Insulation in Vacuum (ISDEIV) - A Novel Vacuum Interruption Contact Design for High Current DC Vacuum Circuit Breaker
摘要： The vacuum interruption contact structure affect the insulation and breaking performance of DC vacuum circuit breaker directly. A novel vacuum interruption contact system with axial magnetic field (AMF)-double transversal magnetic field (TMF) is investigated for high current interruption in DC vacuum circuit breaker in this paper. It consists of one AMF cup-shaped contact and two concentric TMF contacts, which the internal contact is a disk-shaped structure and the external contact is a cup-shaped structure. The so-called novel TMF-TMF-AMF contact structure has the merits of having a very high axial magnetic flux density at large current condition, and producing rotation Lorentz force for metal vapor arc caused during interruption process. Its performance is compared with that of traditional TMF contact, traditional AMF contact and TMF-AMF contacts using three-dimensional finite-element method and the comparison results verify the validity of this proposed interruption contact structure design.
关键词： Lorentz force,vacuum interruption,finite element method,Axial magnetic flux density,metal vapor arc
更新于2025-09-23 15:23:52
-
A Mechanical and modelling study of magnetron sputtered Cerium-Titanium Oxide film coatings on Si (100)
摘要： Ce/Ti mixed metal oxide thin films have well known optoelectrical properties amongst several other physio-chemical properties. Changes in the structural and mechanical properties of magnetron sputtered Ce/Ti oxide thin films on Si (100) wafers with different Ce:Ti ratios are investigated experimentally and by modelling. X-ray Photoemission Spectroscopy (XPS) and X-ray diffraction (XRD) confirm the primary phases as trigonal Ce2O3 and rutile form of TiO2 with SiO2 present in all prepared materials. FESEM imaging delivers information based on the variation of grain size, the mixed Ce/Ti oxides providing much smaller grain sizes in the thin film/substrate composite. Nanoindentation analysis concludes that the pure cerium oxide film has the highest hardness value (20.1 GPa), while the addition of excess titanium oxide decreases the hardness of the film coatings. High temperature in-situ XRD (up to 1000 °C) results indicate high thermal phase stability for all materials studied. The film with Ce:Ti = 68%:32% has a new additional minor oxide phase above 800 °C. Contact angle experiments suggest that the chemical composition of the surface is insignificant affecting the water contact angle. Results show a narrow band of 87.7o to 95.7o contact angle. The finite element modelling (FEM) modelling of Ce/Ti thin film coatings based on Si(100); Si(110); silica and steel substrates shows a variation in stress concentration.
关键词： in-situ X-ray diffraction,Finite element modelling,Nanoindentation,Cerium titanium oxides,Mechanical properties
更新于2025-09-23 15:23:52
-
Definition of design guidelines, construction, and performance of an ultra-stable scanning tunneling microscope for spectroscopic imaging
摘要： Spectroscopic-imaging scanning tunneling microscopy is a powerful technique to study quantum materials, with the ability to provide information about the local electronic structure with subatomic resolution. However, as most spectroscopic measurements are conducted without feedback to the tip, it is extremely sensitive to vibrations coming from the environment. This requires the use of laboratories with low-vibration facilities combined with a very rigid microscope construction. In this article, we report on the design and fabrication of an ultra-stable scanning tunneling microscope (STM) for spectroscopic-imaging measurements that operates in ultra-high vacuum and at low temperatures (4 K). We start from existing designs with sapphire as the main material and improve the stiffness further by performing finite element analysis calculations for the main components of the microscope to guide design choices on the geometry of the parts. With this strategy, we construct a STM head with measured lowest resonant frequencies above f0 = 13 kHz for the coarse approach mechanism, a value three times higher than what has been previously reported and in good agreement with the calculations. This allows us to achieve an average vibration level of ～6 fm/√Hz, without a dedicated low-vibration lab. We demonstrate the microscope’s performance with topographic and spectroscopic measurements on the correlated metal Sr2RhO4, showing the quasiparticle interference pattern in real and reciprocal space with high signal-to-noise ratio.
关键词： ultra-high vacuum,low temperature,spectroscopic imaging,finite element analysis,ultra-stable,scanning tunneling microscopy
更新于2025-09-23 15:23:52
-
Novel research on reliability of silica-based PLC optical splitters
摘要： Environmental, mechanical and optical reliability are basic premises for application of PLC optical splitters. According to temperature and humidity cycling experiment, it demonstrated that insertion loss of PLC optical splitter varies with temperature. Compared to performance at room temperature, the maximum insertion loss change of device is 0.472 dB at 75 °C, and 0.486 dB at ?40 °C. A three-dimensional ?nite element model of PLC chip coupled with ?ber array was established to study the e?ects of temperature on insertion loss. The simulation results match experimental results, indicating that misalignment of PLC chip and ?ber array is the main reason for insertion loss change. It is signi?cant to consider the in?uences of global temperature rather than only paying attention to performance at static temperature when we evaluate the reliability of PLC optical splitters.
关键词： PLC optical splitter,Temperature and humidity,Finite element method,Optical waveguide,Reliability
更新于2025-09-23 15:23:52
-
Geometric parameters effect of the atomic force microscopy smart piezoelectric cantilever on the different rough surface topography quality by considering the capillary force
摘要： Nowadays, the atomic force microscopy (AFM) is widely used in the nanotechnology as a powerful nano-robot. The surface topography in Nanoscale is by far one of the most important usages of the AFM device. Hence, in this article, the vibration motion of a piezoelectric rectangular cross-section micro-cantilever (MC) which oscillates in the moist environment has been examined based on the Timoshenko beam theory. After extracting the MC governing equations according to Hamilton's principle, the finite element method has been used to discretize the motion equations. The surface topography has been simulated for various roughness forms in the tapping and non-contact modes by considering the effects of the Van der Waals, capillary and contact forces. Also, the experimental results obtained from the glass surface topography have been simulated. The results illustrate that the time delay in higher natural frequencies in the tapping mode is shorter in comparison with the non-contact mode, especially, for the lower natural frequencies. The sensitivity analysis of the natural frequencies, topography depth and time delay have been simulated. Results indicate that the most effective parameter is the MC length. In the first mode, the first section length has the highest effect on the surface topography time delay, also, in the second vibration mode; the most effective parameter on the time delay is the MC tip length based on the simulation results.
关键词： AFM piezoelectric micro-cantilever,Timoshenko beam,sensitivity analysis,finite element method,topography depth
更新于2025-09-23 15:23:52
-
Environmentally friendly methodology for fouling removal in pipeline based on leaky guided wave generated by quasi-axisymmetric excitation mode
摘要： In this paper, an environmental and innovative clean technique for pipeline fouling is proposed, which is based on leaky ultrasonic guided waves (LUGWs) generated by quasi-axisymmetric excitation mode. The cavitation, which induced by the LUGWs in liquid medium, is employed for removing fouling inside a pipe. Cavitation corrosion and high-speed jet generated by the collapse of cavitation bubbles destroy fouling layer, and no by-products are formed during the removal process, which means that fouling removal in this way is friendly to the environment. The working frequency is determined by finite element method models and experiment. The effect of removal and its uniformity are measured by mass analysis, scanning electron microscope and energy-dispersive spectroscopy from macro to micro. The descaling experiment results show that the proposed method is able to remove the fouling inside a pipe uniformly.
关键词： Finite element method,Fouling removal,Quasi-axisymmetric,Leaky ultrasonic guided waves
更新于2025-09-23 15:23:52