- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Scalable fabrication of geometry-tunable self-aligned superlattice photonic crystals for spectrum-programmable light trapping
摘要： Superlattice photonic crystals (SPhCs) possess considerable potentials as building blocks for constructing high-performance devices because of their great flexibilities in optical manipulation. From the prospective of practical applications, scalable fabrication of SPhCs with large-area uniformity and precise geometrical controllability has been considered as one prerequisite but still remains a challenge. In this work, we developed an anodic aluminum oxide template-guided approach to realize Ni SPhCs with the maximum area (~500 mm2) ever reported. By virtue of the dual-pore self-alignment effect arising from the periodic anodization electric fields, uniform structures over large areas were obtained for Ni SPhCs. Meanwhile, the geometrical parameters for every array of nanopores in terms of pore depth, size, and morphology can be independently controlled due to the sequential pore-opening. Based on the experimental observation about the geometrical dependence of the light absorption for Ni dual-pore SPhCs, we further fabricated Ni SPhCs with simultaneously-shaped nanopores and nanoconcaves, which not only simplified the fabrication process but also achieved omnidirectional stably-strong (~95%) light absorption spectra. Optical simulations elucidated that surface plasmon resonance and cavity resonance are responsible for the strong light trapping. Notably, the fabrication technique is applicable to Ni SPhCs with different periodicities, leading to spectrally programmable light absorption spectra. With Ni SPhCs as solar absorber, the water evaporation efficiency of a solar steam generation system and the open circuit voltage of a solar thermoelectric generator demonstrated 2.3 and 2.5 times improvement, respectively.
关键词： geometrically tunable,surface plasmon resonance,self alignment,superlattice photonic crystal,cavity resonance,anodic aluminum oxide template
更新于2025-09-19 17:15:36
-
Frequency Comb Generation at 800 nm in Waveguide Array Quantum Well Diode Lasers
摘要： A capacitive-piezoelectric transducer combines capacitive and piezoelectric mechanisms to achieve a combination of electromechanical coupling and Q higher than otherwise attainable by either mechanism separately, has allowed demonstration of a 1.2-GHz contour-mode aluminum nitride (AlN) ring resonator with Q > 3000 on par with the highest measured d31-transduced AlN-only piezoelectric resonators past 1 GHz, and a 50-MHz disk array with an even higher Q > 12 000. Here, the key innovation is to separate the piezoelectric resonator from its metal electrodes by tiny gaps to eliminate metal material and metal-to-piezoelectric interface losses thought to limit thin-film piezoelectric resonator Q, while also maintaining high electric field strength to preserve a strong piezoelectric effect. While Q increases, electromechanical coupling decreases, but the k2 · Q product can still increase overall. More importantly, use of the capacitive-piezo transducer allows a designer to trade electromechanical coupling for Q, providing a very useful method to tailor Q and coupling for narrowband radio frequency (RF) channel-selecting filters for which Q trumps coupling. This capacitive-piezo transducer concept does not require dc-bias voltages and allows for much thicker electrodes that reduce series resistance without mass loading the resonant structure. The latter is especially important as resonators and their supports continue to scale toward even higher frequencies.
关键词： electromechanical coupling,oscillator,Micromechanical resonator,self-alignment,small gap,aluminum nitride,equivalent circuit,quality factor,filter
更新于2025-09-19 17:13:59
-
[IEEE 2019 Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC) - Munich, Germany (2019.6.23-2019.6.27)] 2019 Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC) - Dark Pulses in a Long Ring Laser
摘要： A capacitive-piezoelectric transducer combines capacitive and piezoelectric mechanisms to achieve a combination of electromechanical coupling and Q higher than otherwise attainable by either mechanism separately, has allowed demonstration of a 1.2-GHz contour-mode aluminum nitride (AlN) ring resonator with Q > 3000 on par with the highest measured d31-transduced AlN-only piezoelectric resonators past 1 GHz, and a 50-MHz disk array with an even higher Q > 12 000. Here, the key innovation is to separate the piezoelectric resonator from its metal electrodes by tiny gaps to eliminate metal material and metal-to-piezoelectric interface losses thought to limit thin-film piezoelectric resonator Q, while also maintaining high electric field strength to preserve a strong piezoelectric effect. While Q increases, electromechanical coupling decreases, but the k2 · Q product can still increase overall. More importantly, use of the capacitive-piezo transducer allows a designer to trade electromechanical coupling for Q, providing a very useful method to tailor Q and coupling for narrowband radio frequency (RF) channel-selecting filters for which Q trumps coupling. This capacitive-piezo transducer concept does not require dc-bias voltages and allows for much thicker electrodes that reduce series resistance without mass loading the resonant structure. The latter is especially important as resonators and their supports continue to scale toward even higher frequencies.
关键词： electromechanical coupling,oscillator,Micromechanical resonator,self-alignment,small gap,aluminum nitride,equivalent circuit,quality factor,filter
更新于2025-09-19 17:13:59
-
Self-Aligned Metal Electrodes in Fully Roll-to-Roll Processed Organic Transistors
摘要： We demonstrate the production of organic bottom gate transistors with self-aligned electrodes, using only continuous roll-to-roll (R2R) techniques. The self-alignment allows accurate <5 μm layer-to-layer registration, which is usually a challenge in high-speed R2R environments as the standard registration methods are limited to the millimeter range—or, at best, to tens of μm if online cameras and automatic web control are utilized. The improved registration enables minimizing the overlap between the source/drain electrodes and the gate electrode, which is essential for minimizing the parasitic capacitance. The complete process is a combination of several techniques, including evaporation, reverse gravure, ?exography, lift-off, UV exposure and development methods—all transferred to a continuous R2R pilot line. Altogether, approximately 80 meters of devices consisting of thousands of transistors were manufactured in a roll-to-roll fashion. Finally, a cost analysis is presented in order to ascertain the main costs and to predict whether the process would be feasible for the industrial production of organic transistors.
关键词： roll-to-roll,cost analysis,self-alignment,printing,organic transistor
更新于2025-09-04 15:30:14