- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Highly sensitive and selective room-temperature NO2 gas-sensing characteristics of SnOX-based p-type thin-film transistor
摘要： The high-performance p-type metal-oxide-semiconductor (MOS)-based gas sensor is an important subject of research in the field of gas-sensing technology. In this work, we demonstrated a p-type MOS-based thin-film transistor (TFT) nitrogen dioxide (NO2) gas sensor that used tin oxide (SnOX) for both the channel and sensing layers. The crystalline status, surface morphology, and atomic-bonding configuration of the thin-film were examined using X-ray diffraction, field emission-scanning electron microscopy, and X-ray photoelectron spectroscopy. The results indicated that the deposited thin-film was mainly composed of polycrystalline SnO with a tetragonal structure. The fabricated p-type SnOX TFT showed a maximum response value of 19.4-10 ppm NO2 at room temperature (RT, 25 °C) when operated in the subthreshold region, which was significantly higher than that of 2.8–10 ppm NO2 obtained from a p-type SnOX thin-film chemiresistor at RT. In addition, the SnOX TFT gas sensor showed significantly higher sensitivity to NO2 gas than to other target gases such as NH3, H2S, CO2, and CO at RT. To the best of our knowledge, this is the first study to a p-type MOS-based field-effect transistor-type gas sensor. Our experimental results demonstrate that the p-type SnOX TFT is a promising gas sensor that can operate at RT with high sensitivity and selectivity to NO2 gas.
关键词： SnO,Thin-film transistor,NO2 gas sensing,SnOX,P-type metal oxide semiconductor
更新于2025-11-21 11:01:37
-
α-Fe <sub/>2</sub> O <sub/>3</sub> Polyhedral Nanoparticles Enclosed by Different Crystal Facets: Tunable Synthesis, Formation Mechanism Analysis, and Facets-dependent <i>n</i> -Butanol Sensing Properties
摘要： Three kinds of polyhedral α-Fe2O3 nanoparticles enclosed by different facets including oblique parallel hexahedrons (op-hexahedral NPs), cracked oblique parallel hexahedrons (cop-hexahedral NPs), and octadecahedral nanoparticles (octadecahedral NPs), were successfully prepared by simply changing only one reaction parameter in the hydrothermal process. The structural and morphological of the products were systematically studied using various characterizations including X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), revealing that the three kinds of α-Fe2O3 nanoparticles were enclosed by {104}, {110}/{104}, and {102}/{012}/{104} crystal planes, respectively. The exposed facets and shape of the nanocrystals were found to be affected by the adding amount of ethylene glycol in the solvent. The gas-sensing properties and mechanism of the α-Fe2O3 samples were studied and analyzed, which indicated that the sensitivity of the three samples followed the order of octadecahedral NPs (cid:2) cop-hexahedral NPs (cid:2) op-hexahedral NPs due to the combined effects of specific surface area and oxygen defects in the nanocrystals.
关键词： Polyhedron,n-Butanol,Hydrothermal synthesis,α-Fe2O3 nanoparticles,Gas-sensing
更新于2025-11-14 17:03:37
-
Sol–Gel Spin-Coating Followed by Solvothermal Synthesis of Nanorods-Based ZnO Thin Films: Microstructural, Optical, and Gas Sensing Properties
摘要： Zinc oxide thin films with nanorod morphology were investigated for microstructural and optical properties as well as their performance as a liquid petroleum gas sensing material. A two-step synthesis procedure consisting of sol–gel spin-coating and solvothermal methods was employed where several factors such as rational utilization of metal precursors, solvent, stabilizing, and structure directing agents, a repetitive drying-coating process, as well as post-thermal annealing were found influential to obtain qualified nanorods and a final homogeneous thin film. Compositional and optical investigations were pursued to characterize features, namely morphology, poly crystallinity, porous structure, nanocrystallite size, lattice oriented growth, textural atomic ratio, lattice purity and transparency, phonon and exciton transitions, as well as the formed structural defects via field-emission scanning electron microscopy, x-ray diffraction, energy-dispersive x-ray, UV–Vis spectroscopy, Raman, and photoluminescence techniques. The as-prepared thin film was then used as an active LPG sensing material via a home-made gas sensor where the control sensing parameters were chamber testing temperature and gas concentration. Results showed a quantitative response of 92.7% as sensor sensitivity at an operation temperature of 250°C and a LPG concentration of 800 ppm in addition to fast response and recovery times of 44.1 s and 218.7 s, respectively.
关键词： Zinc oxide nanorods,thin film,optical characteristics,gas sensing,microstructural properties,liquid petroleum gas
更新于2025-09-23 15:23:52
-
A Comparative Study of Gas Sensing Properties of Tungsten Oxide, Tin Oxide and Tin-Doped Tungsten Oxide Thin Films for Acetone Gas Detection
摘要： Nowadays, various metal oxide thin films have been used for the purpose of gas sensing. This research depicts a comparison of gas sensing properties among four different metal oxide thin films, namely, tungsten dioxide (WO2), tungsten trioxide (WO3), tin oxide (SnO2) and tin doped tungsten trioxide (Sn-doped WO3), for detecting acetone gas. Each metal oxide thin film was subjected to acetone gas flow of various concentrations and the corresponding changes in resistance were calculated. Characterizations such as x-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and gas sensing characterization for recording resistance changes have been performed. Each film was annealed at different temperatures for 1 h (WO2 and WO3 at 500°C, SnO2 at 300°C and Sn-doped WO3 at 400°C) so as to achieve an optimum grain size for sensing. The XRD patterns reveal formation of an orthorhombic phase of WO2, hexagonal phase of WO3 and orthorhombic phase of SnO2. AFM and SEM depict clear images of grain boundaries on the film. SnO2 has been found to be the best thin film for sensing acetone gas. Operational optimum temperature for sensing acetone gas has been calculated for each thin film (260°C for WO2, 220°C for WO3, 360°C for SnO2 and 300°C for Sn-doped WO3). It can detect a very low concentration of 1.5 ppm acetone gas with a good resistance response change of 30%. Various concentrations of acetone gas, namely, 1.5 ppm, 3 ppm, 5 ppm, 7 ppm, 10 ppm, 15 ppm and 20 ppm, have been detected using these metal oxide thin films, and thus the comparison has been made. The response time for SnO2 is approximately 3 min and recovery time is approximately 4 min.
关键词： tungsten oxide,acetone gas detection,topography,tin oxide,Metal oxide thin films,surface metrology,gas sensing,tin-doped tungsten oxide
更新于2025-09-23 15:23:52
-
Investigation of Strongly Hydrophobic and Thick Porous Silicon Stain Films Properties
摘要： Porous silicon (PSi) structures with strong hydrophobicity have been achieved by chemical etching of p-type silicon substrates in a solution based on hydrofluoric acid solution (HF) and vanadium oxide (V2O5). The surface morphology and microstructure of the elaborated structured silicon surfaces were investigated using Scanning Electron Microscope (SEM), contact angle and Fourier Transform Infrared spectroscopy (FTIR). The results show that the obtained structures exhibit hierarchically porous surfaces with porous pillars of silicon (PPSi) and an important hydrophobicity of the surface. The electrical properties of those PPSi structures were investigated in presence of 10 ppm of NO2 gas. The response time was about 30s at room temperature. Our results demonstrate that PPSi/Si are highly hydrophobic for long time and suitable for applications in the field of self-cleaning and may be a good candidate in elaborating practical NO2 sensors.
关键词： Porous silicon,Hydrophobicity,Gas sensing applications,Pillars structures
更新于2025-09-23 15:23:52
-
ZnO-enhanced In2O3-based sensors for n-butanol gas
摘要： A series of high-response and fast-response/recovery n-butanol gas sensors was fabricated by adding ZnO to In2O3 in varying molar ratios to form ZnO-In2O3 nanocomposites via a facile co-precipitation hydrothermal method. Morphological characterizations revealed that the shape of pure In2O3 was changed from irregular cubes into irregular nanoparticles, 30-50 nm in size, with the addition of ZnO. Compared with the pure In2O3 gas sensor, the ZnO-In2O3 gas sensor exhibits superior n-butanol sensing performance. With the introduction of ZnO, the response of the sensor to n-butanol was improved from 17 to 99.5 at 180 °C for a [Zn]:[In] molar ratio of 1:1. In addition, the ZnO-In2O3 gas sensors show a reduced optimal working temperature, excellent selectivity to n-butanol, and good repeatability. The response of the ZnO-enhanced In2O3-based sensors showed a strong linear relationship with the n-butanol gas concentration, allowing for the quantitative detection of n-butanol gas.
关键词： ZnO-In2O3,n-Butanol,Gas-sensing property,Selectivity
更新于2025-09-23 15:23:52
-
Light enhanced room temperature resistive NO2 sensor based on a gold-loaded organic–inorganic hybrid perovskite incorporating tin dioxide
摘要： A material is described for sensing NO2 in the gas phase. It has an architecture of type Au/MASnI3/SnO2 (where MA stands for methylammonium cation) and was fabricated by first synthesizing Au/MASnI3 and then crystallizing SnO2 on the surface by calcination. The physical and NO2 sensing properties of the composite were examined at room temperature without and with UV (365 nm) illumination, and the NO2-sensing mechanism was studied. The characterization demonstrated the formation of a p-n heterojunction structure between p-MASnI3 and n-SnO2. The sensor, best operated at a voltage of 1.1 V at room temperature, displays superior NO2 sensing performance. Figures of merit include (a) high response (Rg/Ra = 240 for 5 ppm NO2; where Rg stands for the resistance of a sensor in test gas, and Ra stands for the resistance of a sensor in air), (b) fast recovery (about 12 s), (c) excellent selectivity compared to sensors based on the use of SnO2 or Au/SnO2 only, both at room temperature under UV illumination; (d) a low detection limit (55 ppb), and (e) a linear response between 0.5 and 10 ppm of NO2. The enhanced sensing performance is mainly attributed to the high light absorption capacity of MASnI3, the easy generation and transfer of photo-induced electrons from MASnI3 to the conduction band of SnO2, and the catalytic effect of gold nanoparticles.
关键词： Light absorbing material,SPR effect,Photo generated electrons,Gas sensing,P-n junction,Catalytic effect,Heterojunction,SnO2,UV light,MASnI3
更新于2025-09-23 15:23:52
-
NO2 and H2 sensing properties for urchin-like hexagonal WO3 based on experimental and first-principle investigations
摘要： An intricate sea-urchin-like hexagonal WO3 nanostructure was synthesized by a facile hydrothermal approach. Sensing properties of the as-fabricated sensor exhibited surpassing response and selectivity for NO2 in comparison of H2 after corroborating the composition, phase-purity and surface morphology using X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Formation of the urchin-like structure was ascribed to the capping effects of potassium sulfate that prompts the anisotropic growth of WO3, leading to hierarchical complex with a large surface-volume ratio. In particular, first-principle calculation had provided a new perspective for us to delve into the sensing process of H2 and NO2 from an atomic level. It was found that the sensing properties mainly arose from the tuning of electronic structure and electrons transfer between the adsorbed gas and the sensitized surface along with the charge relocation between them. Finally, a plausible mechanism was proposed as theoretical guidance for achieving high-performance sensors experimentally and supposedly.
关键词： Gas sensing,Surface reaction,First-principles,WO3
更新于2025-09-23 15:23:52
-
Sub-ppm level NO2 sensing properties of polyethyleneimine-mediated WO3 nanoparticles synthesized by a one-pot hydrothermal method
摘要： A novel sensing material of polyethyleneimine-mediated WO3 nanoparticles was prepared by a simple and efficient one-pot hydrothermal method. The structure and morphology characteristics of the as-prepared WO3 nanoparticles were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). The results showed that the as-prepared WO3 nanomaterials were composed of highly dispersible WO3 nanoparticles, and these nanoparticles with the particle size in the range of 10e50 nm showed a monoclinic structure. NO2 sensing measurements demonstrated that WO3 nanoparticles-based gas sensor exhibited superior response, outstanding selectivity, excellent reversibility, and good long-term stability. The sensor response increased as NO2 concentration increased. The highest response value of 251.7 was achieved to 5 ppm NO2 at the optimal operating temperature of 100 (cid:1)C. Especially, the sensor response could reach 3.2e50 ppb NO2. It also exhibited fast response and recovery times with a high sensor response even in a high-humidity environment. The excellent gas sensing properties of WO3 nanoparticles could be ascribed to their high effective surface areas as well as numerous oxygen vacancies, which foresee the great potential application for fast and effective detection of sub-ppm level NO2 under different humidity environments.
关键词： Nanoparticles,NO2,Gas sensing performance,WO3,Hydrothermal
更新于2025-09-23 15:23:52
-
2D ultra-thin WO3 nanosheets with dominant {002} crystal facets for high-performance xylene sensing and methyl orange photocatalytic degradation
摘要： Here we report the synthesis of two-dimensional (2D) ultra-thin WO3 nanosheets (~4.9 nm) with dominant {002} crystal facets through a facile surfactant-induced self-assembly method. It was found that the ultra-thin WO3 nanosheets showed remarkably enhanced xylene sensing performance and methyl orange photocatalytic degradation performance, which could be ascribed to the high percentage of reactive {002} crystal facets (>90%) and high specific surface area (121 m2/g). The mechanism of gas sensing and photocatalysis was systematically studied. This work will be intriguing for designing high-performance metal oxides-based gas sensing and photocatalytic materials through 2D structural modulation and crystal facets engineering, which is important to promote their practical applications in environmental issues.
关键词： {002} crystal facets,2D,Photocatalysis,WO3,Gas sensing
更新于2025-09-23 15:23:52