- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Ultra-flexible perovskite solar cells with crumpling durability: toward a wearable power source
摘要： Perovskite materials hold great potential as photovoltaic power sources for portable devices owing to their mechanical flexibility and high performance; however, the flexibility and e?ciency require further improvement to attain practical viability. We investigated the mechanical fracture behavior of polycrystalline perovskite films by varying the substrate thickness and applying the neutral plane concept. This enabled us to fabricate a crack-free perovskite film on an ultra-thin substrate (B2.5 mm) and to demonstrate ultra-flexible solar cells with high e?ciency (17.03%) with unprecedented flexibility sustained after 10 000 cycles of bending at a 0.5 mm radius. This represents a high e?ciency of 13.6% for large-area flexible perovskite solar cells (1.2 cm2), fabricated by using a hybrid transparent electrode composed of a metal mesh grid and conducting polymer. Using a protective layer to achieve the neutral plane concept, our ultra-flexible perovskite solar cells are demonstrated to be durable even after 100 crumpling cycles. Our approach paves the way to fabricate flexible perovskite solar cells for portable power sources.
关键词： wearable power source,Perovskite solar cells,mechanical durability,neutral plane concept,flexible
更新于2025-11-21 10:59:37
-
Understanding the Impact of Cu-In-Ga-S Nanoparticles Compactness on Holes Transfer of Perovskite Solar Cells
摘要： Although a compact holes-transport-layer (HTL) ?lm has always been deemed mandatory for perovskite solar cells (PSCs), the impact their compactness on the device performance has rarely been studied in detail. In this work, based on a device structure of FTO/CIGS/perovskite/PCBM/ZrAcac/Ag, that effect was systematically investigated with respect to device performance along with photo-physics characterization tools. Depending on spin-coating speed, the grain size and coverage ratio of those CIGS ?lms on FTO substrates can be tuned, and this can result in different hole transfer ef?ciencies at the anode interface. At a speed of 4000 r.p.m., the band level offset between the perovskite and CIGS modi?ed FTO was reduced to a minimum of 0.02 eV, leading to the best device performance, with conversion ef?ciency of 15.16% and open-circuit voltage of 1.04 V, along with the suppression of hysteresis. We believe that the balance of grain size and coverage ratio of CIGS interlayers can be tuned to an optimal point in the competition between carrier transport and recombination at the interface based on the proposed mechanism. This paper de?nitely deepens our understanding of the hole transfer mechanism at the interface of PSC devices, and facilitates future design of high-performance devices.
关键词： perovskite solar cells,compactness,Cu-In-Ga-S,hole transfer,holes transport layer,recombination
更新于2025-11-21 10:59:37
-
Transparent Sn-doped In2O3 electrodes with a nanoporous surface for enhancing the performance of perovskite solar cells
摘要： We report on a simple and efficient process to enhance the performance of perovskite solar cells by using ITO electrodes with a nanoporous surface formed by wet-etching of self-agglomerated Ag nanoparticles. Effective removal of the Ag nanoparticles embedded in the surface of the ITO electrodes result in a nanoporous structure without changing the ITO's sheet resistance (10.17 Ω/square) and optical transmittance (89.08%) at a 550 nm wavelength. Examinations with a scanning electron microscope, a transmission electron microscope, and two-dimensional porous mapping show that the nanoporous ITO surface has an increased contact area with the electron transport layer, which enhanced the carrier extraction efficiency of the perovskite solar cells. Compare to perovskite solar cells fabricated on typical ITO with a flat surface morphology, the perovskite solar cells fabricated on the nanoporous-surface ITO show a higher fill factor of 81.1% and a power conversion efficiency of 20.1%. These results indicate that modified ITO surfaces with nano-scale porosity provide a simple and efficient method to improve the power conversion efficiency of perovskite solar cells without a complicated process.
关键词： Contact area,Nanoporous surface,Sn-doped In2O3,Ag agglomeration,Perovskite solar cells
更新于2025-11-21 10:59:37
-
Iodine Induced PbI <sub/>2</sub> Porous Morphology Manipulation for High-Performance Planar Perovskite Solar Cells
摘要： The quality of the perovskite film has a vital influence on the performance of perovskite solar cells and it is quite desirable to simultaneously manipulate the crystallization and morphology of the perovskite film. In this study, conventional PbI2 is replaced with a PbI2/I2 mixed precursor during the first step of sequential deposition, causing the formation of a PbI2 porous nanostructure. By changing the content of I2 in the precursor, the morphology of the PbI2 film as well as the resulting perovskite film can be successfully modulated. With an optimal content of I2, a high-quality perovskite film with a pure phase and smooth surface can be achieved. As a result, the conversion efficiency of perovskite solar cells using a PbI2/I2 mixed precursor can be as high as 18.63%, compared to 16.89% for the reference device through traditional sequential deposition with a pure PbI2 precursor.
关键词： porous PbI2,iodine,perovskite,sequential deposition,solar cell
更新于2025-11-20 15:33:11
-
Robust CsPbX <sub/>3</sub> (X = Cl, Br, and I) perovskite quantum dot embedded glasses: nanocrystallization, improved stability and visible full-spectral tunable emissions
摘要： Currently, all inorganic perovskite quantum dots (QDs) of cesium lead halides (CsPbX3, X = Cl, Br, and I) have been mainly fabricated using wet chemical methods. Unfortunately, applications of perovskite QDs have been limited due to their poor stability. In the present work, the in situ growth of whole-family CsPbX3 (X = Cl, Br, and I) perovskite QDs in Zn–P–B–Sb based oxide glass via a glass crystallization strategy is reported. The as-prepared CsPbX3 QDs@glass nanocomposites exhibit typical excitonic recombination emissions and superior chemical stability benefited from the protection of the robust inorganic glass matrix. Through modifying the molar ratio of halide sources in glass, multi-color tunable emissions in the entire visible spectral range of 400–750 nm are achieved. As a result, light-emitting diode devices can be constructed by coupling blue-emissive CsPbBrCl2, green-emissive CsPbBr3 and red-emissive CsPbBr0.5I2.5 QDs@glass powders with a commercial ultraviolet chip, yielding bright white light luminescence with excellent optoelectronic performance.
关键词： stability,light-emitting diodes,tunable emissions,glass crystallization,perovskite quantum dots
更新于2025-11-20 15:33:11
-
Multifunctional atomic force probes for Mn2+ doped perovskite solar cells
摘要： Doping in organic–inorganic perovskite semiconductors is an effective method to tailor their optoelectronic properties. In this work, manganese-doped perovskite films with different Mn/Pb ratios ranging from 0% to 2% were systematically studied. The device performance of 0.2% Mn-doped devices was improved compared to that of a device without Mn. However, a further increase of the doping concentration induced a decrease in performance. Several characteristics (especially different scanning probe microscopy characteristics) reveal that an increased dopant concentration results in reduced crystallinity and a change in the film morphology and causes a deterioration in photovoltaic performance for higher dopant concentrations. In the best-performing samples (0.2%), a shift in the valence band level and band gap are found which are responsible for the increased open circuit voltage, while increased grain boundaries and lower surface charge density are responsible for a small reduction in the short circuit current. Thus, multifunctional scanning probe microscopy approaches, combined with different film characterization techniques, offer us effective tools to investigate the impact of doping in the perovskite materials and the corresponding device performance.
关键词： EFM,SKPM,C-AFM,Perovskite solar cells
更新于2025-11-20 15:33:11
-
Novel Ca2GdTaO6:Mn4+,M (M = Li+, Na+, K+, and Mg2+) red phosphors for plant cultivation light-emitting diodes: Synthesis and luminescence properties
摘要： Recently, Mn4+-activated red phosphors are becoming potential color converters for application in indoor plant cultivation light-emitting diodes, owing to their satisfactory luminescence properties as well as low cost. Herein, novel Mn4+-activated double perovskite-type Ca2GdTaO6 phosphors have been synthesized by a high-temperature solid-state reaction method in air, which exhibited a broad excitation band with two peaks locating at 355 nm and 496 nm in range of 250-600 nm and had an intense red emission peaking at 676 nm due to Mn4+:2Eg→4A2g spin-forbidden transition ranging from 650 to 750 nm under 355 nm excitation. Concentration-dependent luminescence properties were studied. The optimal Mn4+ doping concentration in Ca2GdTaO6 host was 0.004, and the concentration quenching mechanism was determined to be a dipole-dipole interaction among Mn4+ ions. Furthermore, the Ca2GdTaO6:0.004Mn4+ phosphor possessed the internal quantum efficiency up to 33% when excited at 355 nm. Besides, the decay lifetimes of Ca2GdTaO6:Mn4+ presented a reasonable downward trend with increasing Mn4+ concentration. In addition, the effect of charge compensation (co-doping of Li+, Na+, K+, and Mg2+ ions) on the luminescent properties of Ca2GdTaO6:Mn4+ phosphors was also investigated.
关键词： Indoor plant cultivation,Ca2GdTaO6,Mn4+,Double perovskite,Luminescence properties,Red phosphor
更新于2025-11-20 15:33:11
-
Defining the composition and electronic structure of large-scale and single-crystalline like Cs2AgBiBr6 films fabricated by capillary-assisted dip-coating method
摘要： Owning the merits of both lead-free and air-stable, the double-perovskite Cs2AgBiBr6 has attracted increasing attention, but suffers low visible-light absorption coefficient due to its large indirect bandgap. Moreover, the electronic structure of its synthesized films has not been explored clearly yet. In this work, we developed a general and promising method to fabricate continuous, uniform and highly orientated Cs2AgBiBr6 films in large scale on various substrates through capillary-assisted dip-coating method. Strikingly, those optimized films are single crystalline verified by 4-scan XRD. Its electronic structure was carefully studied independently by multi-photo-physical characterizations. Its bandgap can be tuned from 2.65 to 2.25 eV by changing the substrate temperature in growth from 40 to 160 °C. Essentially, their work-function (WF) was determined at ~5.01 eV and WF-VBM is around 2 eV. This novel band structure with typical n-type characteristic, was further confirmed by DFT calculations, which reveals that the Cs interstitials and Br vacancies derived deep defect levels were fixed around its Fermi level, closer to the conduction band. This conclusion is different from its widely accepted p-type feature, but definitely deepens our understanding of this material and inspires us to find more valuable strategies of modulating its band structure and optoelectronic properties.
关键词： Single-crystalline perovskite films
更新于2025-11-20 15:33:11
-
Grinding Synthesis of APbX3 (A=MA, FA, Cs; X=Cl, Br, I) Perovskite Nanocrystals
摘要： Currently, metal halide perovskite nanocrystals have been extensively explored due to their unique optoelectronic properties and wide application prospects. In the present work, a facile grinding method is developed to prepare whole-family APbX3 (A=MA, FA and Cs; X=Cl, Br and I) perovskite nanocrystals. This strategy alleviates the harsh synthesis conditions of precursor dissolution, atmosphere protection and high temperature. Impressively, the as-prepared perovskite nanocrystals are evidenced to have halogen-rich surfaces and yield visible full-spectral emissions with maximal photoluminescence quantum yield up to 92% and excellent stability. Additionally, the grinding method can be extended to synthesize widely concerned Mn2+-doped CsPbCl3 nanocrystals with dual-modal emissions of both excitons and dopants. As a proof-of-concept experiment, the present perovskite nanocrystals are demonstrated to be applicable as blue/green/red color converters in UV-excitable white-light-emitting diode.
关键词： perovskite,CsPbBr3,optical materials,luminescence,LED
更新于2025-11-20 15:33:11
-
Single-Composition White Light Emission from Dy3+ Doped Sr2CaWO6
摘要： A series of Dy3+ ion doped Sr2CaWO6 phosphors with double perovskite structure were synthesized by traditional high temperature solid-state method. It was found that there is significant energy transfer between Dy3+ and the host lattice, and the intensities of emission peaks at 449 nm (blue), 499 nm (cyan), 599 nm (orange), 670 nm (red), and 766 nm (infra-red) can be changed by adjusting the concentration of dopant amount of Dy3+ ion in Sr2CaWO6. The correlated color temperature of Dy3+ ion doped Sr2CaWO6 phosphors can be tuned by adjusting the concentration of Dy3+ ion. Upon optimal doping at 1.00 mol% Dy3+, white light with chromaticity coordinate (0.34, 0.33) was emitted under excitation at 310 nm. Thus, single composition white emission is realized in Dy3+ doped Sr2CaWO6.
关键词： double perovskite,energy transfer,white light-emitting,photoluminescence
更新于2025-11-20 15:33:11