- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Laser-arc hybrid welding of 12- and 15-mm thick structural steel
摘要： High-power lasers are very effective in welding of plates thicker than 10 mm due to the keyhole mode. High-power intensity generates a vapor-filled cavity which provides substantial penetration depth. Due to the narrow and deep weld geometry, there is susceptibility to high hardness and weld defects. Imperfections occur due to keyhole instability. A 16-kW disk laser was used for single-pass welding of 12- to 15-mm thick plates in a butt joint configuration. Root humping was the main imperfection and persisted within a wide range of process parameters. Added arc source to the laser beam process may cause increased root humping and sagging due to accelerated melt flow. Humping was mitigated by balancing certain arc and other process parameters. It was also found that lower welding speeds (< 1.2 m/min) combined with lower laser beam power (< 13 kW) can be more positive for suppression of humping. Machined edges provided more consistent root quality and integrity compared with plasma cut welded specimens. Higher heat input (> 0.80 kJ/mm) welds provided hardness level below 325 HV. The welded joints had good Charpy toughness at ? 50 °C (> 50 J) and high tensile strength.
关键词： Mechanical properties,Toughness,Thick steel,Hybrid welding,High strength steel,Laser welding
更新于2025-09-23 15:21:01
-
Filler metal distribution and processing stability in laser-arc hybrid welding of thick HSLA steel
摘要： Welds made by high power laser beam have deep and narrow geometry. Addition of filler wire by the arc source, forming the laser-arc hybrid welding (LAHW) process, is very important to obtain required mechanical properties. Distribution of molten wire throughout the entire weld depth is of concern since it tends to have low transportation ability to the root. Accurate identification of filler metal distribution is very challenging. Metal-cored wires can provide high density of non-metallic inclusions (NMIs) which are important for acicular ferrite nucleation. Accurate filler distribution can be recognized based on statistical characterization of NMIs in the weld. In the present study, it was found that the amount of filler metal decreased linearly towards the root. The filler metal tends to accumulate in the upper part of the weld and has a steep decrease at 45–55 % depth which also has wavy pattern based on longitudinal cuts. Substantial hardness variation in longitudinal direction was observed, where in the root values can reach > 300 HV. Excessive porosity was generated at 75 % depth due to unstable and turbulent melt flow based on morphology of prior austenite grains. The delicate balance of process parameters is important factor for both process stability and filler metal distribution.
关键词： Filler metal distribution,Microstructure,Thick steel,Non-metallic inclusions,High strength steel,Mechanical properties,Laser-arc hybrid welding
更新于2025-09-23 15:19:57
-
Porosity and solidification cracking in welded 45 mm thick steel by fiber laser-MAG process
摘要： Porosity and solidification cracking in joining of thick sections are very common issues in deep penetration keyhole laser-arc hybrid welding (LAHW). In the present work, 45 mm thick high strength steel was joined by a double-sided technique. With combined use of fast welding speeds and larger air gap between plates, higher amount of porosity was found because of the dynamic behavior of the keyhole walls. Solidification cracking formed at the centerline in the bottom of the weld due to high-depth-to-width geometrical ratio. Numerical simulations have been performed and showed very high cooling rate and stresses occurred in the root of the deep welds, which corresponds with higher cracking tendency.
关键词： hybrid welding,mechanical properties,porosity,Laser welding,thick steel,solidification cracking
更新于2025-09-12 10:27:22