- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
A Numerical Study of Densification Behavior of Silicon Carbide Matrix Composites in Isothermal Chemical Vapor Infiltration
摘要： We studied the characteristics of two-scale pore structure of preform in the deposition process and the mass transfer of reactant gas in dual-scale pores, and observed the physiochemical phenomenon associated with the reaction. Thereby, we established mathematical models on two scales, respectively, preform and reactor. These models were used for the numerical simulation of the process of ceramic matrix composites densified by isothermal chemical vapor infiltration (ICVI). The models were used to carry out a systematic study on the influence of process conditions and the preform structure on the densification behaviors. The most important findings of our study are that the processing time could be reduced by about 50% without compromising the quality of the material, if the processing temperature is 950-1 000 ℃ for the first 70 hours and then raised to 1 100 ℃.
关键词： isothermal chemical vapor infiltration,fiber preform structure,densification behavior,ceramic matrix composites,process parameters
更新于2025-09-23 15:23:52
-
Graded‐Index Ytterbium‐Doped Optical Fiber Fabricated through Vapor Phase Chelate Delivery Technique
摘要： Herein, the fabrication of ytterbium-doped graded refractive-index few-mode fiber (GRIN-FMF) is described for the first time following a vapor phase chelate delivery technique. Investigation is carried out to find out the best possible approach to fabricate the preform. The optimization of the process steps along with composition and associated process parameters leads to a parabolic refractive-index profile with a profile parameter of 2 in the developed fiber. A large core of 30 μm diameter and a low numerical aperture (NA) of 0.08 with graded distribution of dopant ions is achieved with a good repeatability. Amplification gain of more than 20 dB with good beam quality for pulses with kW peak power without any distortion in temporal, spectral, and spatial profile proves the potential of the fiber for many promising applications.
关键词： preform fabrication,graded-index fibers,ytterbium,vapor phase chelate delivery,fiber lasers
更新于2025-09-19 17:13:59
-
Investigation of p+ emitter formation for n-type silicon solar cells application
摘要： Investigation of p+ emitter formation for n-type silicon solar cells application. This work reports on the study of boron diffusion in n-type silicon from preform source for p+ emitter formation. Using quartz tube furnace, three main parameters are investigated that are: drive-in temperature, drive-in time and temperature ramp-up time. It is found that the sheet resistance as measured by the four point probe method (4-pp) decreases from 93 Ω/□ to 24 Ω/□ as the drive-in temperature increases from 850°C to 950°C, likewise, it decreases from 57 Ω/□ to 38 Ω/□ as the drive-in time increases from 20 min to 40 min. The electrically active boron dopant profiles as measured by the electrochemical capacitance voltage technique (ECV) exhibit surface concentrations below the solid-solubility limit of boron in silicon for all the studied emitters, the maximum surface and peak boron concentrations of 1.30x1020 and 1.58x1020 atoms/cm3 were measured respectively on the emitter which is formed at a drive-in temperature of 950°C. Furthermore, it is revealed from the secondary ion mass spectroscopy measurements (SIMS) the presence of the boron rich layer (BRL) on its surface. The Hall Effect measurement method is used for measuring sheet resistance and sheet charge carrier concentration.
关键词： N-type silicon,Boron dopant profile,Solar cells,Preform source,Boron diffusion
更新于2025-09-12 10:27:22
-
Stress-induced refractive index changes in laser fibers and preforms
摘要： Refractive index profile of the core is a key design parameter in fiber lasers and amplifiers. During manufacturing, the initial information of the index profile is obtained from the preform, while ultimately the performance is defined by the index profile of the fiber. Depending on stresses and diffusion, the two profiles may be different. It is possible to predict more accurately the laser fiber refractive index when we apply a stress-induced index change model to the measured preform index profile data. The improved capability to predict the fiber index from preform increases the confidence in achieving the designed index profile in fiber, which enables faster process feedback and higher fiber yields.
关键词： laser fiber,tension,optical fiber,modelling,thermal stress,preform,Refractive index change,DND,stress
更新于2025-09-11 14:15:04