- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Biocompatible and sustainable power supply for self-powered wearable and implantable electronics using III-nitride thin-film-based flexible piezoelectric generator
摘要： Energy harvesters that scavenge biomechanical energy are promising power supply candidates for wearable and implantable electronics. Of the most widely used energy harvesters, piezoelectric generators can generate more electric charge than their triboelectric counterparts with similar device size, thus are more suitable to make compact wearable devices. However, most high-power piezoelectric generators are made from lead zirconate titanate, making them undesirable for wearable applications due to the toxic lead element. In this study, a flexible piezoelectric generator (F-PEG) is fabricated with chemically stable and biocompatible Group-III-nitride (III-N) thin film by a layer-transfer method. The III-N thin-film F-PEG can generate an open-circuit voltage of 50 V, a short-circuit current of 15 μA, and a maximum power of 167 μW at a load resistance of 5 M?. Applications of the III-N thin-film F-PEG are demonstrated by directly powering electronics such as light-emitting diodes and electric watches, and by charging commercial capacitors and batteries to operate an optical pulse sensor. Furthermore, the III-N thin-film F-PEG shows good durability and a stable output after being subjected to severe buckling tests of over 30,000 cycles.
关键词： flexible,piezoelectric generators,thin film,III-nitride,self-powered system,biocompatible
更新于2025-09-23 15:23:52
-
Determination of the appropriate piezoelectric materials for various types of piezoelectric energy harvesters with high output power
摘要： For a type-1 piezoelectric energy harvester (PEH), in which stress develops in the supporting system of the piezoelectric materials, the electromechanical coupling factor (kij) of the piezoelectric materials is important for the output power at the resonance frequency. Therefore, soft-piezoelectric materials are good candidates for these PEHs. For type-2 PEHs, in which stress develops in the piezoelectric material and supporting system, the figure of merit (FOM) of the output power at the resonance frequency is (kij2×Qm)/s11E, where Qm and s11E are the mechanical quality factor and the elastic compliance of piezoelectric materials, respectively. In particular, the effect of Qm is very large for these PEHs, indicating that hard-piezoelectric materials are good candidates for type-2 PEHs operating at the resonance frequency. For both type-1 and type-2 PEHs operating at off-resonance frequency, the kij2×dij×gij is the FOM of the output power of the PEHs, where gij is a piezoelectric voltage constant. Therefore, soft-piezoelectric materials are also good candidates for both type-1 and type-2 PEHs operating at the off-resonance frequency.
关键词： PEH,Piezoelectric materials,FOM,kij,Qm
更新于2025-09-23 15:23:52
-
Nanomechanical, Mechanical Responses and Characterization of Piezoelectric Nanoparticle-Modified Electrospun PVDF Nanofibrous Films
摘要： Limitless implementations of nanofibrous membrane show the importance of understanding the nanomechanical responses for water purification and piezoelectric nanogenerator applications. Here, the polyvinylidene fluoride (PVDF) electrospun nanofibrous films doped by 0.01, 0.05 and 0.1 wt% of ZnO nanoparticles were prepared in the method of electrospinning. Characterizations of PVDF nanocomposite fibrous films were inspected using field emission scanning electron microscope, thermogravimetric analysis, water contact angle, uniaxial tensile test and nanoindentation technique. The influence of minimal concentration of piezoelectric nanoparticles on the morphological, water contact angle, dynamic water contact angle, piezoelectric, thermal and mechanical stabilities of nanocomposite fibrous films was examined. The nanoscale mechanical properties of the PVDF/ZnO nanofibrous films were performed by nanoindentation technique at different spots of nanofibrous mat to examine the elastic–plastic behavior of membranes. The eventual ZnO nanoparticle-modified nanofibrous membranes have been shown nano-level fibers, considerable hydrophilicity and preferable thermal, mechanical and piezoelectric properties. The doping of polymer by 0.1 wt% of ZnO nanoparticles exposed significant enhancement of thermal, mechanical and nanomechanical responses of the melting temperature 2% (170–173 °C), tensile strength 20% (2.418 MPa), elastic modulus 18% (2.418 GPa) and hardness 60% (235 MPa) and piezoelectric coefficient 13.42 pC/N of the nanofibrous films. These understandings of nanoscale properties are highly promising in the development of sensor and actuators, biomedical, energy harvesting and water filtration devices.
关键词： Thin films,Nanomechanical responses,Nanofibers,PVDF,Piezoelectric nanoparticles,Electrospinning
更新于2025-09-23 15:23:52
-
Electric field-induced toughening in GaN piezoelectric semiconductor ceramics
摘要： In this paper, the effect of an applied electric field on fracture toughness of polarized GaN piezoelectric semiconductor ceramics was studied by using experimental and numerical methods. The results show that fracture toughness increases by 22% under a field intensity of 0.83 kV cm?1, and with further increase of the electrical filed, fracture toughness remains unchanged. This is completely different from the fracture characteristics of traditional piezoelectric ceramics that is thought to decrease with an applied electric field. The reason for such a difference is attributed to the redistribution of free electrons. It is expected that this finding will be instructive to the reliability design of piezoelectric semiconductor structures and devices.
关键词： GaN,Electric field,Fracture toughness,Piezoelectric semiconductor ceramics,Toughening
更新于2025-09-23 15:23:52
-
Internal-field-dependent low-frequency piezoelectric energy harvesting characteristics of in situ processed Nb-doped Pb(Zr,Ti)O3 thin-film cantilevers
摘要： Piezoelectric thin-film-based cantilevers have been investigated for higher energy-harvesting performance with simplified processing steps. Here, a simple in situ film deposition process of heavily Nb-doped lead zirconate titanate (PZT) films, which does not require annealing and poling, has been demonstrated to verify the possibility of use of the resultant films as energy-harvesters specifically for low frequency vibrating sources. The in situ domain formation of the films during the deposition was demonstrated from the apparent shifts of the capacitance-electric field curves, indicating the presence of internal electric fields. The so-called imprint behavior was found to be directly related to the performance of piezoelectric energy harvesting. As an optimal example, 12 mol% Nb-doped cantilever harvesters that showed the largest imprint behavior exhibited the best values of ~19.1 GPa figure-of-merit and ~1436 mWcm?3g?2 power density, which are competitive compared to other reported values.
关键词： Thin films,Cantilevers,Piezoelectric energy harvesting,Nb-doping,PZT
更新于2025-09-23 15:23:52
-
Fabrication of PAN/ZnO Nanofibers by Electrospinning as Piezoelectric Nanogenerator
摘要： Piezoelectric nanogenerator is a material that is used for converting mechanical energy to electrical energy. This research aimed to study the piezoelectric nanogenerator properties in PAN/ZnO nanofibers layered on the stainless-steel substrate. ZnO nanoparticles that were used in this work were synthesized by coprecipitation method. The ZnO nanoparticles were mixed with PAN dissolved with DMF. Fabrication of PAN-ZnO nanofibers was done using the electrospinning method on the stainless-steel substrate. The formed PAN/ZnO nanofibers were then characterized using XRD, SEM, and FTIR. To test the piezoelectric nanogenerator properties, PAN/ZnO nanofibers were combined to PAN nanofibers and coated on the stainless-steel substrate to form piezoelectric nanogenerator device. This device was then connected to an electrometer and an oscilloscope to measure the current and voltage resulted after bending. The results of XRD of ZnO nanoparticles had the wurtzite crystal structure with the size of about 46 nm. Meanwhile, the PAN/ZnO had an amorphous structure. The test results of piezoelectric nanogenerator properties showed the value of voltage and current of 7.22 V and 47.48 μA, respectively. PAN/ZnO nanofibers on the stainless-steel substrate are potential to be the material of piezoelectric nanogenerators in general.
关键词： electrospinning,PAN/ZnO nanofiber,energy harvesting,piezoelectric nanogenerator
更新于2025-09-23 15:23:52
-
[IEEE 2018 IEEE International Symposium on the Physical and Failure Analysis of Integrated Circuits (IPFA) - Singapore (2018.7.16-2018.7.19)] 2018 IEEE International Symposium on the Physical and Failure Analysis of Integrated Circuits (IPFA) - Characterization of Multilayered Ceramic Capacitors via Piezoelectric Force Microscopy
摘要： The coupling between an electrical and mechanical response in a material is a fundamental property that provides functionality to a variety of applications ranging from sensors and actuators to energy harvesting and biology. Most materials exhibit electromechanical coupling in nanometer-sized domains. Therefore, to understand the relationship between structure and function of these materials, characterization on the nanoscale is required. This property can be directly measured in a non-destructive manner using piezoelectric force microscopy (PFM), a mode that comes standard in all atomic force microscopes (AFMs) from Park Systems. Additionally, PFM can be used as a spectroscopic tool to evaluate switching of piezoelectric domains. Here we demonstrate the utility of PFM for failure analysis of a multilayered ceramic capacitor. Correlative imaging of topography and electrical signals revealed discontinuous structures in the device that likely had a direct effect on device performance. Spectroscopy was also performed at a specific piezoelectric region to measure domain properties, such as the electric field required to flip the polarization direction (coercive voltage).
关键词： topography,atomic force microscopy,multilayered ceramic capacitor,electromechanics,piezoelectric microscopy,polarization,failure analysis
更新于2025-09-23 15:23:52
-
Composite BNT-BT0.08/CoFe2O4 with core-shell nanostructure for piezoelectric and ferromagnetic applications
摘要： In this work, we report on the synthesis and characterization of BNT-BT0.08/CoFe2O4 biphasic composite with core-shell structure. This artificial core (BNT-BT0.08)/shell (CoFe2O4) heterostructure was prepared by sol-gel method and the resulting composite was characterized in term of microstructure, dielectric, piezoelectric and magnetic properties. BNT-BT0.08/CoFe2O4 sintered ceramic shows high permittivity (ε′ ≥ 30) and high dielectric losses (tan δ ≥ 10) in the low frequency range (ν ≤ 104 Hz), remnant polarization (Pr) of ～7.7 μC/cm2 and, remanent magnetization (Mr) of 24 emu/g at 5 K and of 14 emu/g, at room temperature. The present study reveals that the ferroelectric, piezoelectric and magnetic properties of this new architectured composite depend on the amount of each component and, can be tailored by adjusting their synthesis conditions. BNT-BT0.08/CoFe2O4 core-shell material investigated in this work provides a novel way to exploit new applications for the multifunctional composite, such as piezoelectric sensor, magnetoelectronic sensors and data storage devices.
关键词： Sol-gel processes,Composite core-shell,((Bi0.5Na0.5)0.92Ba0.08TiO3),Cobalt ferrite (CoFe2O4),Lead-free piezoelectric
更新于2025-09-23 15:23:52
-
Inverse size-dependence of piezoelectricity in single BaTiO3 nanoparticles
摘要： The piezoelectric charge coefficients d33 of single BaTiO3 (BT) nanoparticles (NPs) were characterized using a transmission electron microscope (TEM) that is equipped with a precise charge meter and an in-situ TEM indentation holder that enables controlled compression experiments. An exceptionally high d33 of 1775 pC/N was obtained in NPs that are smaller than the critical diameter (D; typically known as < 100 nm) that has been regarded as the lower limit to permit for ferroelectricity in BT. The mechanical conversion efficiency of piezoelectric BT nanogenerators enhanced as D of BT NPs was decreased; this result corresponds with the single-NP compression measurements of d33. This quantification of the effect of D in ferroelectric materials may guide development of efficient and high-powered nanostructured piezoelectric energy devices such as piezoelectric nanogenerators.
关键词： in-situ TEM,size effect,STEM,Ferroelectric,piezoelectric,nanogenerator
更新于2025-09-23 15:23:52
-
Synthesis and characterization of nanofiber-type hydrophobic organic materials as electrodes for improved performance of PVDF-based piezoelectric nanogenerators
摘要： Poly(3,4-ethylenedioxythiophene) (PEDOT) derivatives are synthesized by oxidative polymerization using sodium dodecyl sulfate (SDS) as an anionic surfactant dopant. The resulting polymeric materials featuring nanofiber-type one-dimensional (1D) structures are identified as poly(2-butyl-2,3-dihydrothieno[3,4-b][1,4]dioxine:dodecyl sulfate (PEDOT-C4:DS) and poly(2-hexyl-2,3-dihydrothieno[3,4-b][1,4]dioxine:dodecyl sulfate (PEDOT-C6:DS). The ratio of the DS anion doped into PEDOT-C4:DS and PEDOT-C6:DS is 0.16 and 0.23, respectively. The contact angle of water on the PEDOT-C4:DS and PEDOT-C6:DS films is 76.6° and 87.7°, respectively, showing hydrophobic properties similar to that with water on PVDF. It facilitated the fully uniform film formation due to excellent surface matching. Peeling force of PEDOT-C4:DS and PEDOT-C6:DS is stronger than the one of PEDOT:PSS-CNT composite. GIWAX analysis showed that PEDOT-C4:DS formed the highly ordered edge-on structure and PEDOT-C6:DS formed the bimodal orientation consisting of edge-on structure mainly and face-on structure slightly. The electrical conductivity (σPEDOT-C4:DS=50.0 S cm-1) of PEDOT-C4:DS is 41.7 times higher than that of PEDOT:PSS (σPEDOT:PSS=1.2 S cm-1). The output signals (maximum voltages/currents) of piezoelectric nanogenerators (PNGs, electrode/PVDF/electrode) using these materials as electrodes are PNG-1 (PEDOT:PSS-CNT composite) 1.25 V/128.5 nA, PNG-2 (PEDOT-C4:DS) 1.54 V/166.0 nA, and PNG-3 (PEDOT-C6:DS) 1.49 V/159.0 nA. Of these, PNG-2 & PNG-3 show maximum piezoelectric output power of 63.0 nW and 59.9 nW at 9 MΩ compared to PNG-1 (41.0 nW at 10 MΩ). They are enhanced up to 53.7%. The excellent surface matching between a piezoelectric active material and an electrode material leads to high output power.
关键词： 4-ethylenedioxythiophene) derivative,poly(3,nanofibrillar network,piezoelectric nanogenerator,nanofiber,hydrophobicity
更新于2025-09-23 15:23:52