- 标题
- 摘要
- 关键词
- 实验方案
- 产品
-
Analysis of Cu doping concentration on PbS thin films for the fabrication of solar cell using feasible nebulizer spray pyrolysis
摘要： This report portrays the analysis of Cu doping concentration (%) on PbS thin films prepared by feasible nebulizer spray technique. The doping percentage of Cu was increased from 0% to 8% in steps of 2%. X-ray diffraction study of the films evinces the nature of the films as polycrystalline with simple cubic crystal structure. The calculated crystallite size was varied from 55 to 41 nm on increasing the Cu doping concentration. SEM/AFM studies proclaim that the cubic shaped grains have covered the entire film surface. The shape of grains was amended with respect to the increase in Cu doping concentration. An elevation in band gap from 1.61 eV to 2.10 eV was spotted for the raise in Cu doping concentration from 0% to 6%. The near band edge emission peak at 575 nm was sensed from PL spectra in which the intensity was enhanced. Hall Effect measurement declared the p-type conductivity nature for the prepared PbS films. Resistivity and carrier-concentration values are 0.73×103 Ωcm and 6.04×1013 cm-3 respectively for 6% Cu doped PbS thin films. Efficiency for the solar cell FTO/n-CdS/p-Cu:PbS structure constructed with 6% Cu doped PbS film is about 0.68%.
关键词： X-ray diffraction,PL spectra,Hall Effect measurement,AFM/SEM,Cu doped PbS film
更新于2025-11-21 11:18:25
-
Development of a high strength Al–Zn–Si–Mg–Cu alloy for selective laser melting
摘要： Despite additive manufacturing processes are already widely used in several industrial applications, there are few materials that are specifically designed and optimized for these technologies. Currently, only few Al alloys are available on the market and employed for 3D printing of structural parts. In particular, SieMg bearing alloys are the most common Al alloys for additive manufacturing, featuring high processability but moderate mechanical properties. By this work, we studied the effect of Si addition on the hot cracking susceptibility of a high strength AleZneMgeCu alloy. A preliminary activity has been carried out by blending AleZneMgeCu and AleSieMg powders and analysing their microstructure and properties achieved after selective laser melting. Eventually a new AleZneSieMgeCu alloy has been designed, produced as powder alloy by gas atomization and tested. The microstructure and phase transformations of the new alloy has been investigated by synchrotron X-ray diffraction, differential scanning calorimetry and microscope analysis. The AleZneSieMgeCu alloy processed by selective laser melting featured a relative density of 99.8%, no hot cracks were noticed within the investigated microstructures. The ability of the new alloy to respond to aging starting from both as built and solution annealed conditions has been also evaluated. A good response to direct aging (directly from as built condition) was demonstrated, featuring yield strength and ultimate tensile strength of 402 and 449 MPa, respectively, and hardness of 174 HV after optimized aging at 165 (cid:1)C for 2 h.
关键词： Differential scanning calorimetry,Metal additive manufacturing,Mechanical properties,Synchrotron X-ray diffraction,High strength Al alloy
更新于2025-11-21 11:18:25
-
Mono and co-substitution of Sr2+ and Ca2+ on the structural, electrical and optical properties of barium titanate ceramics
摘要： In this work, Ba0.9Sr0.1TiO3, Ba0.7Sr0.3TiO3, Ba0.5Sr0.5TiO3, Ba0.5Ca0.25Sr0.25TiO3 and Ba0.5Ca0.5TiO3 have been synthesized to evaluate the influence of mono and co-substitution of A-site dopants (Sr2+ and Ca2+) on the structural, electrical and optical properties of BaTiO3 ceramics. Sr2+ added samples showed a tetragonal structure which became slightly distorted with increasing Sr2+ concentration and finally achieved a cubic structure for x = 0.50. Ba0.5Ca0.5TiO3 also retained their tetragonality with limited solubility. Presence of second phase, CaTiO3 demonstrated the fact of restricted solubility. The concurrent effect of Sr2+ and Ca2+ didn't alter the tetragonal structure. Sr2+ substitution enhanced the apparent density as well as grain size which stimulated the domain wall motion and improved dielectric properties. However, the ferroelectric nature of Ba1-xSrxTiO3 was poor due to the redistribution of point defect at grain boundary. The optical band gap was found to be reduced from 3.48 eV to 3.28 eV with increasing Sr2+ content. Co-substitution of cations improved the electrical property significantly. The highest value of dielectric constant was found to be ～547 for Ba0.5Ca0.25Sr0.25TiO3 ceramics. Both Ba0.5Ca0.25Sr0.25TiO3 and Ba0.5Ca0.5TiO3 had developed P-E loop having lower coercive field and moderate optical band gap energy. Co-doping with Sr2+ and Ca2+ was a good approach enhancing materials electrical as well as optical property.
关键词： Dielectric properties,Grain size,X-ray diffraction,Optical properties,Sintering
更新于2025-11-21 11:18:25
-
Influence of bath temperatures on physical and electrical properties of potentiostatically deposited Cu2O thin films for heterojunction solar cell applications
摘要： In the present work, the influence of bath temperatures on structural, morphological, vibrational, optical, electrical and photo response properties of the electrochemically deposited cuprous oxide (Cu2O) thin films on fluorine doped tin oxide substrate is extensively investigated with the help of X-ray diffraction (XRD), scanning electron microscopy (SEM), Micro Raman spectroscopy, photo luminescence (PL) spectroscopy, UV–visible spectroscopy, LCR measurement, Keithley 4200 semiconductor characterization system respectively. XRD patterns reveal that the deposited Cu2O films have cubic structure grown along the preferential (111) orientation and the film deposited at 40 °C shows better crystalline nature when compared at 55 and 70 °C. The micro structural properties of films such as crystallite size (D), dislocation density (δ), micro strain (ε) and stacking fault probability (α) were calculated and discussed in detail. SEM displays a well-defined three side pyramid shaped morphology for the film deposited at 40 °C. Micro Raman and PL spectra reveal the film deposited at 40 °C by being better crystalline at a higher acceptor concentration. UV–Visible study shows that the optical energy band gap increases from 2.05 to 2.17 eV with an increase in bath temperature from 40 to 70 °C. The frequency-temperature dependence of impedance analysis shows a higher electrical conductivity for a film deposited at 40 °C compared to other bath temperatures. I-V measurement illustrates a good photoconductivity response for Cu2O thin film deposited at 40 °C compared to films deposited at 55 and 70 °C.
关键词： Micro Raman spectroscopy,X-ray diffraction,Photoconductivity,Cuprous oxide,Pyramid shape
更新于2025-11-19 16:46:39
-
Structural and optical properties of a revived Pb0.5Ba1.5BiVO <sub/>6</sub> perovskite oxide
摘要： The polycrystalline ceramic Pb0:5Ba1:5BiVO6 manifesting the complex double perovskite structure was tailored by the conventional solid state route at a moderate temperature. Qualitative phase analysis and formation of the ceramic were affirmed by XRD analysis. The X-ray powder diffraction pattern of the compound explored at room temperature affirms the single phase formation with double perovskite structure exhibiting rhombohedral phase. Microstructural analysis of the studied compound procured from the Scanning Electron Microscope (SEM) validates the formation of dense microstructures and nonuniformly distributed grains with minimal voids. Compositional analysis was shaped through the Electron Diffraction Spectroscopy (EDS) confirming the absence of contamination of any other metals apart from the mentioned ones. Dielectric (Cr and tan δ) parameters of the compound were studied using the LCR analyzer at different temperatures and wide range of frequencies. The polarization and dielectric study affirms the presence of ferroelectricity in the material with transition temperature much above the room temperature. The tangent dielectric loss of this sample being almost minimal at room temperature attributes it to find applications in different grounds of electronics. Optical equities of the ceramic were further analyzed by the RAMAN, FTIR, UV–Vis and Photoluminescence spectroscopy.
关键词： EDS,Ceramic,X-Ray diffraction,LCR,optical properties
更新于2025-11-14 14:48:53
-
Physical, Thermal and Spectroscopic Studies on Biofield Treated p-Dichlorobenzene
摘要： Para-dichlorobenzene (p-DCB) is widely used as a chemical intermediate in manufacturing of dyes, pharmaceuticals, polymers and other organic synthesis. The aim of present study was to evaluate the impact of biofield treatment on physical, thermal, and spectroscopic properties of p-dichlorobenzene. The p-dichlorobenzene sample was divided into two groups that served as treated and control. The treated group received Mr. Trivedi’s biofield treatment. Subsequently the control and treated samples were evaluated using X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and UV-Vis spectroscopy. XRD result showed an increase in crystallite size (4.93%) along with alteration in peak intensity of treated sample as compared to control. Furthermore, DSC analysis results showed that the latent heat of fusion of treated p-dichlorobenzene was considerably reduced by 8.66% as compared to control. The reduction in melting point of treated sample (54.99°C) was also observed as compared to control (57.01°C) p-dichlorobenzene. Moreover, TGA/DTG studies showed that Tmax (temperature, at which sample lost maximum of its weight) was increased by 6.26% and weight loss per degree celsius (°C) was decreased by 12.77% in biofield treated p-dichlorobenzene as compared to control sample. It indicates that thermal stability of treated p-dichlorobenzene sample might increase as compared to control sample. However, no change was found in UV-Vis spectroscopic character of treated p-dichlorobenzene as compared to control. These findings suggest that biofield treatment has significantly altered the physical and thermal properties of p-dichlorobenzene, which could make it more useful as a chemical intermediate.
关键词： Differential scanning calorimetry,Para-dichlorobenzene,Thermogravimetric analysis,and UV-Visible spectroscopy,Biofield treatment,X-ray diffraction study
更新于2025-09-23 15:23:52
-
A Mechanical and modelling study of magnetron sputtered Cerium-Titanium Oxide film coatings on Si (100)
摘要： Ce/Ti mixed metal oxide thin films have well known optoelectrical properties amongst several other physio-chemical properties. Changes in the structural and mechanical properties of magnetron sputtered Ce/Ti oxide thin films on Si (100) wafers with different Ce:Ti ratios are investigated experimentally and by modelling. X-ray Photoemission Spectroscopy (XPS) and X-ray diffraction (XRD) confirm the primary phases as trigonal Ce2O3 and rutile form of TiO2 with SiO2 present in all prepared materials. FESEM imaging delivers information based on the variation of grain size, the mixed Ce/Ti oxides providing much smaller grain sizes in the thin film/substrate composite. Nanoindentation analysis concludes that the pure cerium oxide film has the highest hardness value (20.1 GPa), while the addition of excess titanium oxide decreases the hardness of the film coatings. High temperature in-situ XRD (up to 1000 °C) results indicate high thermal phase stability for all materials studied. The film with Ce:Ti = 68%:32% has a new additional minor oxide phase above 800 °C. Contact angle experiments suggest that the chemical composition of the surface is insignificant affecting the water contact angle. Results show a narrow band of 87.7o to 95.7o contact angle. The finite element modelling (FEM) modelling of Ce/Ti thin film coatings based on Si(100); Si(110); silica and steel substrates shows a variation in stress concentration.
关键词： in-situ X-ray diffraction,Finite element modelling,Nanoindentation,Cerium titanium oxides,Mechanical properties
更新于2025-09-23 15:23:52
-
Preparation of high-quality stress-free (001) aluminum nitride thin film using a dual Kaufman ion-beam source setup
摘要： We proposed and demonstrated a preparation method of (001) preferentially oriented stress-free AlN piezoelectric thin films. The AlN thin films were deposited by a reactive sputtering technique at substrate temperatures up to 330 °C using a dual Kaufman ion-beam source setup. We deposited the AlN on Si (100), Si (111), amorphous SiO2, and a (001) preferentially oriented Ti thin film and compared their crystallographic, optical, and piezoelectric properties. The AlN thin films deposited on the (001) preferentially oriented Ti thin films have the highest crystallographic quality. The stress-free AlN reached a high value of the piezoelectric coefficient d33 = (7.33 ± 0.08) pC·N?1. The properties of the AlN thin film prepared at such low temperatures are suitable for numerous microelectromechanical systems, piezoelectric sensors, and actuators monolithically integrated with complementary metal-oxide-semiconductor signal-processing circuits.
关键词： Ellipsometry,Aluminum nitride thin film,Optical properties,d33 piezoelectric coefficient,Kaufman ion-beam source,Ion-beam sputtering deposition,(001) preferential orientation,X-ray diffraction
更新于2025-09-23 15:23:52
-
New blue phosphorescence from trifluorosulfonyl-substituted iridium complexes
摘要： For color-pure phosphorescence organic light emitting diodes (PHOLEDs), we synthesized the trifluoromethyl sulfonyl substituted ligand and two new blue Iridium complexes with perfluoro-sulfonyl group (SOCF3pic and SOCF3mpic). The both iridium complexes showed similar photophysical and thermal properties while the HOMO energy leves of two Iridium complexes slightly differnet to be -5.84 eV for SOCF3pic and -5.74 eV for SOCF3mpic, respectively. The device with the SOCF3mpic dopant exhibited higher device efficiencies of 7.17 cd/A and 3.7 % compared to that with the SOCF3pic dopant (4.03 cd/A and 2.78 %). Two-dimensional GIXD images of scattered X-ray intensity from surface to full depth for SOCF3pic-doped and SOCF3mpic-doped TCTA:4PTPS films were characterized for preferential orientation along the out-of-plane direction.
关键词： preferential orientation along the out-of-plane direction,blue phosphorescence,iridium complex,grazing incidence wide-angle X-ray diffraction,organic light emitting diodes
更新于2025-09-23 15:23:52
-
Photocatalytic oxidation of aromatic alcohols over silver supported on cobalt oxide nanostructured catalyst
摘要： In this paper, we report an in-situ synthesis of silver supported on cobalt oxide (Ag/Co3O4) nanoparticles (NPs) and studied the catalytic activity of this material as an eco-friendly, simple, recyclable and efficient catalyst for one‐pot photocatalytic oxidation of aromatic alcohols. Ag nanoparticles with the sizes of 2–5 nm supported on spherical Co3O4 with the radius between 40 and 60 nm were synthesized by homogeneous chemical precipitation followed by hydrothermal heating. The as-synthesized catalyst was thoroughly characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), elemental mapping, transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and N2 adsorption-desorption isotherm (BET) analysis. It was observed that the catalysts with 1 wt% of silver loading shows high activity and selectivity toward the target aldehyde product. The effects of different reaction parameters such as reaction time, oxidant and solvent were investigated and studied in detail. The synergistic effect between the surface Ag NPs and Co3O4 nanospheres plays a vital role toward very high catalytic activity.
关键词： Oxide materials,Chemical synthesis,Catalysis,X-ray diffraction
更新于2025-09-23 15:23:52